Marantz RC5400 Manual de usuario

Model RC5400 User GuideTouch Screen Remote Control

User Guide6Turning on the Touch ScreenTap the Touch Screen gently with your finger or a blunt, softobject like a pencil eraser.The display is activate

ModesThe RC5400 has different “Modes”. When you activate the RC5400for the first time, it starts up in USE mode allowing you toimmediately operate you

The commands assigned to the device button called the Device Action.Device Overview —The Device Overview page also displays a list of all the devices

User Guide93. Press and hold either of the two Left and RightFunction buttons, then tap the device you would like tojump to. No input select command

User Guide10Page Scroll — you can navigate the pages by pressing thePage + and Page - buttons on the left side of RC5400. Cursor Navigation — This fu

You can operate the devices using two kinds of buttons;Soft buttons - Virtual buttons on the Touch Screen.Hard buttons - Seven buttons below the scree

4. Check Battery Life- The Information PageAccess the Information page by tapping the INFO button in theUPPER TOOL BAR. You can check;The percentage o

First Setup pageSetting Function AdjustingTime Mode Sets the time display mode. Tap the “Time Mode” button(AM/PM, 24H, No Time) Repeatedly.Time, Day,

User Guide14RC5400 provides different modes. For customizing your RC5400you have to switch to the appropriate mode via the Mode Menupage. The mode men

User Guide15Getting StartedTo switch to another mode1 Tap the label of the mode (i.e ) you are using in theLOWER TOOL BAR. The Mode Menu page appears.

For US and CanadaFCC Compliancy: This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to part 15 o

User Guide16It is best to proceed with customizing in several stages. The first stage is to teach all of your existing remote codes to theRC5400. The

User Guide17Customizing your RC54007 Switch back to DELETE mode and delete the device if it is not agood match to your component. Repeat steps 4 throu

User Guide18Customizing Your RC5400If your entire system is new to you, practice using the RC5400manually for a few days before programming any macros

The problems don’t stop with powering up a system. Often, you willwant to construct a macro to watch or listen to a specific source. Thismay require t

User Guide201 Write a list of all of the actions in the operation you want torecord.2 Gather all of the remote controls you will need for the operatio

User Guide21Macros allow you to send a sequence of commands, jumps, delaysand beeps with up to 250 steps using one single touch.Basically, you can ass

User Guide22Customizing Your RC5400You cannot jump to any Home page, Device Overview andPage Overview page. You are only allowed to jump to first page

User Guide23You will do all of your Macro/Jump programming within a screenthat will appear after you press the Macro button on the Modemenupage. Befor

User Guide249 Navigate to your new macro device and press your newlynamed macro button to enter the MACRO edit page. The MACRO edit page will appears.

User Guide2512 Typically you will need to adjust the timing of the macro. Simplyputting in lots of delays will make the macro work, but maymake the ma

Dear customer,Please be informed that this carton only contains a copy of the user manual in English. ForGerman, French, Dutch, Spanish and Italian pl

You program the RC (Remote Control)commands by transmittingIR (infrared) signals from your existing remote controls to theRC5400’s learning eye. To d

User Guide27ReferenceYou cannot program the buttons in the Devece Overview pagedirectly. You have to program them using Learn device actionfunction (

Reference8 Return to the Mode Menu page by tapping label in theLOWER TOOL BAR.9 Return to USE mode by pressing the Left Function buttonlabeled Exit

User Guide29ReferenceHard buttons can be programmed for a device specific commandfor a particular device on the remote (Programming locally).Only via

User Guide30The following elements can be labeled: Buttons on a device pageand Home page, Page (the name that appears on the PageOverview page), and D

User Guide316 Edit the label.n To delete a character, press the Right Function button labeled Delete .n To change the font size, Tap the + or - bu

User Guide32Labeling a DeviceYou can label all devices which are displayed in the DeviceOverview page.1 Tap and hold the MODE icon in the LOWER TOOL B

User Guide33If you have a device that is not provided in the Device Overviewpage, you can add it to the RC5400.There are two possible ways to add a de

User Guide34Receivers are both A/V Amps and Tuners - Since you typicallyuse the two sections of your Marantz receiver at different times, wehave separ

User Guide35ReferenceHELP - This template is used to create a Help List that will helpusers through a multiple step process that cannot be reliablypro

Automating Your Home Theater With The Marantz RC5400 RC5400 Remote Control User GuideThe information in this manual is copyright-protected. No part o

User Guide36Reference4 You can add the device with or without RC codes.n Create with RC codes: Choose this option if you have theexact Marantz compone

User Guide37You can delete the Buttons in device pages and the Device itself.Note Left, Right Function, Home buttons, Pages and Frames (textswith non-

User Guide38Deleting a Device1 Tap and hold the MODE icon in the LOWER TOOL BARmore than 3 seconds. Mode Menu page will appear.2 Tap the DELETE butt

User Guide39You can change the order of device buttons in the Device Overviewpages. 1 Tap and hold the MODE icon in the LOWER TOOL BARmore than 3 seco

Macro Page NotationBefore you begin to program a Macro, study the notation used inthe MACRO mode. Each type of action has its own notation. User Guide

User Guide41Recording a Macro to a Operation Button Step By Step1 Tap and hold the MODE icon in the LOWER TOOL BARmore than 3 seconds. Mode Menu page

User Guide42ReferenceThere are two extra commands you can record as any step in amacro;Recording a Device Action (Source or Input Switching)To record

User Guide43ReferenceEditing MacrosYou can edit any macro you have recorded.1 Tap and hold the MODE icon in the LOWER TOOL BARmore than 3 seconds. Mo

User Guide44Warning To use the Remote Control with Radio Frequency (RF) you needan Marantz RX-77 RF Extender. This is an optional accessory for the RC

User Guide453 Select the device for which you want tochange the IR / RF settings. The IR / RF setting page appears. The reversed color button labeled

User Guide1Introduction 21. The Marantz RC5400 22. The Battery 3Getting Started 61. Activating the RC5400 62. Navigating the RC5400 73. Operating

User Guide46ReferenceChoosing Another ChannelWhen you notice RF interference or unreliable operation you shouldtry choosing another channel to operate

User Guide47ReferenceUpload and download new configurations to and from yourRC5400. You do this with the USB cable supplied with yourRC5400 connected

User Guide48Maintaining Your RC5400Important noticeTake care not to scratch the Touch ScreenUse your finger to tap the Touch Screen or use plastic-tip

User Guide49TroubleshootingGeneral ProblemsThe display is blank Tap the screen to make sure the RC5400 is turned on. Adjust the screen contrast usin

User Guide50TroubleshootingProgramming ProblemsHard buttons are not sending the correct commands Check whether the button is programmed per device or

User Guide51TroubleshootingThe TV goes blank or the input source changes The Device Overview page item might be programmed to switchthe input source.

User Guide52Frequently Asked QuestionsCan I program a device button to execute more than onecommand?Yes, you can. You can program a macro to the devic

User Guide53Frequently Asked QuestionsHow do I calibrate the Touch Screen?The RC5400 is calibrated when it leaves the factory, so normallyyou do not h

PauseStopPlay, Normal run, normal speedReverse Play, Normal run, normal speedFast Forward, Scan Forwards, Fast run, fast speedRewind, Scan Backwards,

Page number upPage number downPage enlargementTV and text mixed1st or 2nd languageLast view, previous programPower, Stand-byZone focus: long distanceZ

User Guide2The RC5400 is designed to control most devices that understandinfrared (IR) remote control signals. Its easy-to-use Touch Screen andits int

User Guide56SpecificationsHardware High-resolution (320 x 240) monochrome LCD 16 grey scales with digital contrast controlBlue EL backlighting for LCD

IndexUser Guide57AActivating 6Pickup sensor 6, 14ADD mode 33Switch Modes 15AMPS 34Copy Existing Device 33Create New Device

User Guide58IndexDDay 13Delay 22, 40DELETE Mode 37Button 37Device 38Undo 37Device Action 8, 24, 42Device Menu 13Device

User Guide59IndexJJump 42LCD Sleep 13Learning 26Locally 28Low Battery Icon 5Lower System Area 3LLABEL Mode 30Button 30

User Guide60NNavigating 7Cursor Navigation 9Device Action 8Device Overview page 8Device Scroll 9Home Page 7Devices 7Pages

User Guide61Software Version 12Specification 56Memory 56Option 56Symbols 31, 54System Requirement 47TTab Button 10Tap Tech

User Guide62Service and SupportFor service and support, please contact your Marantz authorizeddealer or Marantz customer service. On the Marantz inter

User Guide63Memo

www.marantz.comYou can find your nearest Marantz authorized dealer or distributor on our website.JAPAN Marantz Japan, Inc. 7-35-1 Sagami Ohno, Sagamih

The Touch ScreenWhen you use the RC5400 for the first time, you will have to:• Install the battery pack.• Place the RC5400 in the docking station (DS5

User Guide4Installing the Battery Pack1 Press the latch on the battery cover and remove the batterycover from the RC5400.2 Plug the cable of the batte

Charging the RC5400 For charging the RC5400, you use the docking station DS5400.1 Connect the power adapter to the docking station and plug itinto a w